Paint – It’s Constituents, Properties and Types

Paints are applied on the surfaces of timber, metals and plastered surfaces as a protective layer and at the same time to get pleasant appearance. Paints are applied in liquid form and after sometime the volatile constituent evaporates and hardened coating acts as a protective layer.

 

CONSTITUENTS OF PAINT

The following made up a Paint

[1] BASE

It is a principal constituent of paint. It also possesses the binding properties. It forms an opaque coating. Commonly used bases for paints are white lead, red lead, zinc oxide, iron oxide, titanium white, aluminium powder and lithophone. A lead paint is suitable for painting iron and steel works, as it sticks to them well. However it is affected by atmosphere action and hence should not be used as final coat. While zinc forms good base but is costly.

Lithophone, which is a mixture of zinc sulphate and barytes, is cheap. It gives good appearance but is affected by day light. Hence it is used for interior works only.

[2] VEHICLES

The vehicles are the liquid substances which hold the ingredients of a paint in liquid suspension and allow them to be applied on the surface to be painted. Linseed oil, Tung oil and Nut oil are used as vehicles in paints. Of the above four oils, linseed oil is very commonly used vehicles. Boiling makes the oil thicker and darker. Linseed oil reacts with oxygen and hardens by forming a thin film.

[3] PIGMENTS

Pigments give required colour for paints. They are fine particles and have a reinforcing effect on thin film of the paint. The common pigments for different colours are:

Black – Lamp black, suit and charcoal black.
Red – venedion red, red lead and Indian red.
Brown – burned timber, raw and burned sienna
Green – chrome green, copper sulphate.
Blue – prussian blue and ultra marine
Yellow – ochre and chrome yellow.

CHECK OUT  37 Amazing Stairs Design Picture you Must See
[4] DRIER

These are the compounds of metal like lead, manganese, cobalt. The function of a drier is to absorb oxygen from the air and supply it to the vehicle for hardening. The drier should not be added until the paint is about to be used. The excess drier is harmful because it destroys elasticity and causes flaking.

[5] THINNER

It is known as solvent also, It makes paint thinner and hence increases the coverage. It helps in spreading paint uniformly over the surface Terpentine and neptha are commonly used thinners. After paint applied, thinner evaporates and paint dries.

 

PROPERTIES OF A PAINT

[1] Paint should be possible to apply easily and freely.

[2] Paint should dry in reasonable time.

[3] Paint should form hard and durable surface.

[4] It should not be harmful to the health of workers.

[5] It should not be easily affected by atmosphere.

[6] It should possess attractive and pleasing appearance.

[7] Paint should form a thin film of uniform nature i.e., it should not crack.

[8] It should possess good spreading power.

[9] It should be cheap.

 

TYPES OF PAINT

Depending upon their constituents there are various types of paints. A brief description of some of them which are commonly used are given below:

[1] OIL PAINT

These paints are applied in three coats-primer, undercoat and finishing coat. The presence of dampness while applying the primer adversely affect the life of oil paint. This paint is cheap and easy to apply.

[2] ENAMEL PAINT

It contains white lead, oil, petroleum spirit and resinous material. The surface provided by it resists acids, alkalies and water very well. It is desirable to apply a coat of titanium white before the coat of enamel is applied. It can be used both for external and internal walls.

[3] EMULSION PAINT

It contains binding materials such as polyvinyl acetate, synthetic resins etc. It dries in 12 hours and it is easy to apply. It is more durable and can be cleaned with water. For plastered surfaces, first a coat of cement paint should be applied and then the emulsion point. Emulsion paint needs sound surfaces.

CHECK OUT  Different Types of Mortar and Tests on Mortar
[4] CEMENT PAINT

It is available in powder form. It consists of white cement, pigment and other additives. It is durable and exhibits excellent decorative appearance. It should be applied on rough surfaces rather than on smooth surfaces. It is applied in two coats. First coat is applied on wet surface but free from excess water and allowed to dry for 24 hours. The second coat is then applied which gives good appearance.

[5] BITUMINOUS PAINT

This type of paint is manufactured by dissolving asphalt or vegetable bitumen in oil or petroleum. It is black in colour. It is used for painting iron works underwater

[6] SYNTHETIC ROBBER PAINT

This paint is prepared from resins. It dries quickly and is little affected by weather and sunlight. It resists chemical attack well. This paint may be applied even on fresh concrete. Its cost is moderate and it can be applied easily.

[7] ALUMINIUM PAINT

It contains finely ground aluminium in spirit or oil varnish. It is visible in darkness also. The surfaces of iron and steel are protected well with this paint. It is widely used for painting gas tanks, water pipes and oil tanks.

[8] ANTI CORROSION PAINT

It consists essentially of oil, a strong dier, lead or zinc chrome and finely ground sand. It is cheap and resists corrosion well. It is black in colour. Application of Paint Preparation of surface for application of paint is the most important part in painting. The surface to be painted should not be oily and it should be from flakes of the old paint. Cracks in the surface should be filled with putty and then with sand paper. Then primer is applied. Painting work should be carried out in dry weather. The under coats and first coats must be allowed to dry before final coat is applied.

CHECK OUT  Bamboo And Reinforcement Steel Bars As Structural Member In Building Construction
[9] DISTEMPER

Distempers are the cheaper variety of paints in which chalk is used as base and water is used as a carrier. The emulsifying agent which is commonly used is glue or casein. Distempers are available in powder form or in the form of paste.

They are to be mixed with hot water before use. The surface to be distempered should be thoroughly rubbed and cleaned. The cracks, if any should be filled by lime putty. The surface should be kept dry for about two months before applying distemper. Thus a primary coat is applied and is allowed to dry. Distemper is usually applied in two coats.

Distemper got the following properties:

[1] They are generally light in colour.

[2] The coatings are generally thick.

[3] They give reflective coating.

[4] They are less durable than oil paints but are cheaper.

[10] VARNISH

Varnish is the solution of resins or resinous substances like amber, copal, shellac, gum resin etc. in solvents like oil, turpentile, alcohol etc. Depending upon the solvents used varnishes are classified as, oil varnishes, turpentile varnishes, spirit varnishes and water varnishes.

The desirable characteristics of an ideal varnish are:

[1] It should give glossy surface.

[2] Should be durable.

[3] It should dry rapidly after application.

[4] It should not develop cracks after drying.

[5] It is commonly used on wooden surfaces.

 

Love this post and you love to get a copy

Click on the button below to get the PDF file and Read Offline.

Enter your Comment....

This site uses Akismet to reduce spam. Learn how your comment data is processed.